Strip Plus – Acid Activated Chlorinated Solvent

Strip Plus

Epoxy & Polyester Coating Remover

Designed for the safe removal of Polyester and Acrylic Powder Coatings.

Strip Plus is an acid-activated chlorinated solvent containing formic acid, methylene chloride, methanol, wetting agents and corrosion inhibitors.  It is designed as a cold solvent stripper to be used in immersion tanks for the removal of difficult organic coatings including polyesters, vinyls, epoxies, and acrylics off the ferrous and non-ferrous metals.

The Benefits

  • Strip Plus  has a water seal to prevent evaporation.
  • Strip Plus  can be neutralised  easily.
  • Strip Plus  also removes epoxy coatings.
  • Strip Plus  does not require Toxic label.

Advantages

  • Removes difficult paint coatings such as polyesters, vinyls, epoxies, and acrylics.
  • Safe on ferrous metals and aluminium.
  • Used at room temperature.
  • Rapid stripping action.
  • Rinses easily with water.
  • Water borne upper phase minimises the evaporation of methylene chloride.

Where to use

Strip Plus is recommended for use in the Powder Coating and associated Industries.

How to use

Strip Plus is easy to use. Immerse components into Dip-tank and allow product to work. After soaking, remove and rinse off

Use Instructions

Strip Plus is designed to be used as supplied at ambient temperatures.  Tank construction should be 2S or 3S aluminium, 316 stainless steel, or porcelain.  Immerse parts to be stripped allow to soak for the necessary period of time.  Rinse off with a pressure water rinse.  Iron and steel parts should be put through a neutralization step in the solution of Arven HIB Plus if rust prevention is desired.  This application would be carried out after a good pressure water rinse.

Technical Properties

  • Appearance: Clear diphase liquid
  • Odour: Pungent
  • Specific gravity @ 20°C: 1.250 typical
  • Flash point: None

Caution

  • Do not use Strip Plus near open flame or on a very hot metal surfaces as toxic vapours (phosgene gas) may be evolved?
  • Do not use Strip Plus on magnesium, zinc or tin-containing metal alloys as discolouration or etching or dissolution of metals may occur.

Full instructions are on the Drum.

Enquire

To buy or enquire about a product call:
01928 576262

Stripol LF – Low Foam Ink Remover & Floor Polish Stripper

Stripol LF

Low Foam Ink Remover, Floor Polish Stripper and Polyelectrolyte Remover.

Specially formulated to remove water based inks, polish, paint, oil, grease and wax build up and Clean polyelectrolytes from Water Authority Machinery.

The Benefits

  • Stripol LF is sure, safe and effective.
  • Stripol LF cuts cleaning & stripping time by half.
  • Stripol LF dilutes 10-1 with hot water making it very economical.
  • Stripol LF can be used as a general cleaner at low dilution.

Where to use

  • Stripol LF is highly recommended for use in the Water Industry for cleaning polyelectrolytes from the machinery and the Floors, walls and other surfaces.
  • Stripol LF is extremely effective for the removal of water based inks used in the cardboard carton printing industry.
  • Stripol LF is also recommended for use in Offices, Warehouses, Dance halls, Clubs, Hospitals, Leisure Centres, Indoor Sports Arenas and anywhere that polished floors need to be cleaned
    prior to re-polishing.

How to use

Stripol LF is very easy to use. Simply dilute 10-1 with hot water. Allow to soak for 5 – 10 minutes. Scrub, and rinse off with water.

Full instructions are on the Container.

Enquire

To buy or enquire about a product call:
01928 576262

Tarslip – Solvent Free Bitumen & Asphalt Release Agent

Tarslip

Solvent Free Bitumen and Asphalt Release Agent

Modern formulation designed to eliminate the problem of unwanted bitumen sticking to various surfaces such as vehicles and masonry.

The Benefits

  • Tarslip is ready to use.
  • Tarslip provides a slippery surface to prevent sticking.
  • Tarslip does not damage Bitumen or Asphalt.
  • Tarslip is Biodegradable.
  • Tarslip is coloured blue to help achieve a visible, even cover.

Where to use

  • Tarslip can be used in all industries where the use of Bitumen and Asphalt cause a problem such as Petrochemical companies, Power stations, Fire brigades, Docks and Harbour authorities Building sites and Road surfacing outlets.
  • Tarslip will completely protect against the adhesion of Bitumen and Asphalt to any surface therefore saving on the very costly exercise of replacing brickwork or time spent on cleaning.
    Its main use is for coating tipper bodies to ensure the complete load is discharged.

How to use

Tarslip is very easy to use. Simply spray, pour or brush on to  surface to be coated.

Full instructions are on the Drum.

Enquire

To buy or enquire about a product call:
01928 576262

Xtrakleen, Xtrakleen 2, and Xtrakleen LF – Extra Strength Cleaner

Xtrakleen

Extra Strength Hard Surface Cleaner

Specially formulated for use in scrubber dryers, sweepers and hot & cold pressure washers.

The Benefits

  • Xtrakleen is extremely economical with a dilution rate of up to 180-1 with water.
  • Xtrakleen can be used in all types of machines and pressure washers.
  • Xtrakleen will extend the life of the cleaning pad.
  • Xtrakleen easily removes even the most stubborn stains.
  • Xtrakleen is completely biodegradable

Where to use

Xtrakleen is specifically designed as a general hard surface cleaner for use in all types of industry to clean Warehouses , Factory floors, Road signs, Crash barriers and Garage forecourts.

How to use

Scrubber dryers and sweepers.
Light Soiling  12-1   Medium Soiling  10-1  Heavy Soiling  8-1

Rotary floor maintenance machines
Light Soiling  12-1   Medium Soiling  10-1  Heavy Soiling  8-1

Hot or cold high pressure water washers
Light Soiling 180-1  Medium Soiling 90-1  Heavy Soiling  50-1

  • Xtrakleen is available in 210lt Drums and 1000lt IBCs
  • Xtrakleen 2 is also available and is a diluted version for ease of handling.
  • Xtrakleen is also available as a Low Foam Formulation

Full instructions are on the Container.

Enquire

To buy or enquire about a product call:
01928 576262

Zolvitt Plus – Powerful, Viscous, Surface Coating & Graffiti Remover

Zolvitt Plus

Powerful, Viscous, Surface Coating & Graffiti Remover

Specially formulated to remove all forms of surface coatings including Paint, Varnish, Resin, Adhesives, Inks, Carbon and Graffiti. It will even soften extremely resilient coatings such as Epoxy resins, PVA and Enamel for easy removal.

The Benefits

  • Zolvitt Plus replaces the harsher solvents normally required for Graffiti, Paint & Carbon removal.
  • Zolvitt Plus is non-acidic, non-alkaline and non- toxic.
  • Zolvitt Plus is non-chlorinated and safe to use.
  • Zolvitt Plus is biodegradable.
  • Zolvitt Plus helps to preserve the environment and does not damage the Ozone Layer.
  • Zolvitt Plus does not run enabling it to work more effectively on the disfigured area.

Where to use

  • Zolvitt Plus can be used in many industries including Printing. Flooring, Enameling, Fibreglass, Paint and Varnish producers, for the removal of Ink, Paint, Varnish and all forms of Resin.
  • Zolvitt Plus can also be used by all outlets where graffiti Problems occur i.e. Councils, Hospitals, Leisure Centres, Bus Depots, Stations etc.

How to use

  • Zolvitt Plus is very easy to use. Simply brush onto the surface to be cleaned. Allow the product to penetrate and dissolve the contaminants. Wipe off with an absorbent cloth or wash off with water.
  • Zolvitt Plus can also be used in the Arven Dip Tank

Full instructions are on the Drum.

Enquire

To buy or enquire about a product call:
01928 576262